50 Spring Street
Ramsey, NJ 07446, U.S.A.
Tel: 201-934-8500 Fax: 201-934-9832
www.bogen.com
54-9260-01A
Printed in U.S.A. 0303
© 2003 Bogen Communications, Inc. All rights reserved.
Specifications subject to change without notice.
fold marks
fold marks
fold marks
fold marks
Power Vector Series
Modular Amplifiers
Convenient Signal Processing,
Input Flexibility,
And More Power!
Models V250,V150,V100,
V60 and V35
BALANCED INPUT (BAL2S)
Stereo, balanced input module
• Stereo, high-impedance, balanced inputs
• Dual gain 0 dB/18 dB
• Professional-quality, low noise performance
• Mutable by higher priority modules
• Variable ducking level when muted
• Fade back from mute
• Screw terminal connections
TELEPHONE INPUT (TEL1S)
Telephone interface input module
• Loop start or ground start trunk interfacing
**
• Dry loop interface to paging ports
• Audio-activated paging in dry loop
• Gain/Trim control
• Noise gate w/Threshold control
• Limiter w/Threshold control
• Bus assignable & Transformer-isolated
• Mute send & receive
*
• Screw terminal connections
BRIDGING INPUT (BRG1R)
Provides buffered input feed to other amplifiers
• Input signal available at buffered output
• Gain/Trim control
• Ground isolated input to eliminate ground loop
• Mute send & receive
*
• Variable ducking level when muted
• Fade back from mute
• Buffered output not muted
• Bus assignable
• RCA connectors
MICROPHONE INPUTS (MIC2S, MIC2X)
Low-impedance, electronic-balanced microphone input modules
• Gain/Trim control
• Hi-Cut/Lo-Cut controls
• Voice Enhance control
• Noise gate w/Threshold control
• Limiter w/Threshold control
• 24V Phantom power
• Mute send & receive
*
• Bus assignable
• Screw terminals (MIC2S)
• XLR connector (MIC2X)
MICROPHONE INPUTS (MIC1S, MIC1X)
Low-impedance, transformer-balanced microphone input modules
• Gain/Trim control
• Bass & Treble controls
•
Noise gate w/Threshold & Duration
• Limiter w/Threshold control
• 24V Phantom power
• Mute send & receive
*
• Bus assignable
• Screw terminals (MIC1S)
• XLR connector (MIC1X)
MONO AUX INPUT (MAX1R)
Unbalanced mono input module
• Gain/Trim control
• Bass & Treble controls
• Variable ducking level when muted
• Mute send with threshold/duration adjust
• Mute send & receive
*
• Fade back from mute
• Bus assignable
• RCA connector
STEREO AUX INPUT (SAX1R)
Unbalanced stereo input module
• Gain/Trim control
• Bass & Treble controls
• Variable ducking level when muted
• Mute send with threshold/duration adjust
• Mute send & receive
*
• Fade back from mute
• Stereo-to-mono summing option
• Bus assignable
• RCA connectors
TRANSFORMER BALANCED INPUT (TBL1S)
Transformer balanced AUX input module
• Tr ansformer-isolated line level input
• Gain/Trim control
• Bass & Treble controls
• Mute send with threshold/duration adjust
• Mute send & receive
*
• Variable ducking level when muted
• Fade back from mute
• Screw terminal connections
TONE GENERATOR INPUT (TNG1S)
Multiple tone generator input module
• Select from burst/steady, slow whoop, siren,
mechanical bell, Klaxon, night ringer, double
chime, and doorbell tones
• Select 4 of 8 tones to trigger
• Momentary & continuous playback modes
• Microprocessor-controlled operation
• Mute send & receive
*
• Screw terminal for 4 external
trigger connections
Performance Specifications
Power Output (RMS):
Rated: 250W 150W 100W 60W 35W
Typical @ 1 kHz:* 340W 200W 140W 85W 45W
Frequency Response
Transformer: 45-20 kHz; 0/-2 dB
Direct: 20-20 kHz; 0/-1 dB
Distortion
Transformer: 0.5%**
Direct: 0.1%** (.05% typical @ 1 kHz)
Signal-to-Noise
†
Fundamental: -94 dB
With Aux Module: -70 dB
With Mic Module: -60 dB
With Tel Module: -70 dB
Tone Controls
Bass Frequency: 100 Hz (+/- 10 dB minimum)
Treble Frequency: 10 kHz (+/- 10 dB minimum)
Low Cut Frequency: 125 Hz @ -6 dB/octave
Sensitivity 0.4V (at module bay connector)
Output Regulation: 2 dB or better, no load to full load
Output Impedance
Transformer-Coupled: 70V, 25V, 8 ohms (bal or unbal)
Direct Coupled: 4 ohms
Inserts
Insert "OUT" Level: 1VRMS (@FRP)
Insert "OUT" Impedance: 50 ohms maximum
Insert "IN" Sensitivity: 1VRMS
Insert "IN" Impedance: 10k ohms minimum
Pre-EQ Output
Output Level: 4VRMS (@FRP)
Output Impedance: 50 ohms maximum
AC Power Receptacle: 500 watts maximum power, unswitched
AC Voltage: 120V AC, 60Hz
AC Current: 5.5A 3.5A 2.0A 1.3A 0.6A
Product Weight (lb.): 40 35 32 28 24
Dimensions: 17" W x 3-1/2" H x 13-1/2" D (all models)
MODELS V250 V150 V100 V60 V35
* Typical, @1 kHz/0.1% THD/4Ω ** THD+N, Maximum, Full bandwidth @ FRP
†
Referenced to FRP output level, 20-20 kHz bandwidth limited
PARAMETRIC EQUALIZER (PEQ1R)
• 2 full parametric bands
• Frequency control
• ‘Q’ bandwidth control
• Gain control
• Bass and Treble control
• Unbalanced input
• Bypass switch
• Mutable input
(lowest priority only)
• Gradual fade back from mute
COMPRESSOR LIMITER (CMP1R)
• Compressor Ratio control
• Threshold control
• Make-up Gain control
• Bypass switch
• Unbalanced input
• Gradual fade back from mute
• Mutable input
(lowest priority only)
AMBIENT NOISE SENSOR (ANS1R)
• Maximum Gain control
• Ramp Speed control
• Activity Threshold control
• Ambient mic input threshold control
• Stereo Aux input (summed mono)
• Aux level input control
• Defeatable
• Gradual fade back from mute
• Connect up to 4 sensor mics
(1 included)
• Mutable Input (lowest priority only)
PLUG-IN MODULES
+
OUTPUT
Modules
INPUT
Modules
Power Vector Amplifier Series
+
Modules Sold Separately
* Module can mute or be muted by other modules. ** Loop and Ground Start applications require an external 48V Power Supply - Bogen PRS48 recommended.
New PowerVector5.0 3/28/03 10:14 AM Page 1
Kommentare zu diesen Handbüchern