UTI1 shown with optional
rack mount / security cover kit
Programmable AUX Relay
The UTI1 provides a way for in-
stallers to decide how the AUX
relay contacts will trip based on
which inputs on the UTI1 are ac-
tive. The UTI1 has 4 inputs:
override, tone trigger, paging,
and night ring. The installer can
program the AUX relay to re-
spond to one or any combination
of these inputs. The UTI1 priori-
tizes these inputs (in the order
shown above) so that higher pri-
ority inputs preempt lower ones,
but the AUX relay contacts can be
programmed to work independ-
ently of this hierarchy.
For example, the AUX relay could
be programmed to respond only
to a night ring trigger independent
of anything else the UTI1 was
doing. The UTI1 would suppress
the night ring tone if a general
page were made; however with
the AUX relay programmed this
way, the AUX relay contacts
would remain active until the
night ring input stopped regard-
less of the other UTI1 inputs.
The AUX relay contacts can also
be programmed to operate after
the triggering event has finished.
In this case, the AUX relay contact
activates for 1 second and then
stops. This type of operation allows
external equipment to be triggered
after an event has occurred.
All this selectable functionality
allows the installer improved
ways to control external equip-
ment in conjunction with the
UTI1 operation. Programming is
accomplished through simple
DTMF programming codes.
Accessories
RPKUTI1
Security Cover & Rack Mount Kit
(sold as a set)
Single-Zone Universal Telephone
Interface
UTI1
Product Features:
Power
Dimensions
Product
Requirements Weight
120V AC,
12-1/4" W X 5-1/4" H X 2-1/2" D
5 lb.
0.5A (without rack mount kit)
Bogen’s UTI1 is a single-zone telephone interface that is compatible with all standard analog
port types. A background music (BGM) input with variable muting coordinates music and
page announcements. An additional audio output provides a “page only” function
(no BGM) for application flexibility. A built-in 24V DC, 1A power supply is provided for pow-
ering amplified speakers. Paging volume controls are provided for each of the outputs. An out-
put limiter function, with limiter active indicator, provides consistent page volume regardless
of loud or soft paging announcements. Contact-triggered tones and night ring signals, as
well as programmable AUX relay contacts, are all programmed using DTMF tones through the
dual-purpose override input. Plug-in terminal strips provide for easy installation. An optional
security cover/rack mount kit (RPKUTI1) is available.
• Emergency override & general paging
• One-way paging only
• Interfaces to Loop Start, Ground Start,
Analog Station, and Page Ports (with
or without contact closure activation)
• Simple 2-switch interface setup
• Background music (BGM) input with level
control and variable muting
• Separate Page & BGM and Page Only
(no BGM) outputs
• Level control for each output
• 24V DC, 1A power supply
•
150 Speaker T/R drive capacity per output
• Page level limiter with active indicator
• Adjustable automatic level control
• Override input (loop start or page port)
• Contact-triggered Night Ring input
• Programmable AUX Relay
• Pre-announce/confirmation tone
• Tone burst (2 to 7 sec), chime,
and slow whoop tone selections
• Microcontroller operated, DTMF
programmable
• Night ring tone or chime selection
• Setup test tone
• Pluggable terminal strip connectors
• Programming through override jack
• Programmable timeout for station mode
• Programmable trunk port timeout
• Responds to CPC disconnect signal
• Wall-mount design
•
Rack-mountable with RPKUTI1 kit (optional)
• FCC Part 68 Registered
• Listed to UL Standard 60950
for US and Canada
UTI1 Control Panel
SINGLE-ZONE TELEPHONE INTERFACE
www.bogen.com
31
PAGING CONTROL
Kommentare zu diesen Handbüchern